Insulation
Insulation adds energy savings and slope under the rubber.
Flat Roofing
Rubber Roof Installation Millburn, NJ
A roofer in Millburn can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, with as few seams as possible. Dial (973) 858-1841 to talk with a local roofer about a new rubber roof.
Rubber roofing usually means EPDM, though some people use the term for any single-ply membrane. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. That flexibility is why it suits so many homes.
Attachment method shapes the rest of the installation. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. For homes, adhered EPDM is the most common choice.
Two more decisions round out the plan. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black is standard and holds heat, while white reflects it. The installer also plans how the membrane laps under shingles above it and up the wall beside it, where leaks tend to start.
Many rubber roof installation calls in Millburn also turn up a need for rubber roof repair or flat roof installation.
Need rubber roof installation in Millburn? Call (973) 858-1841 to talk to a local roofer.
Call nowThe process
The rubber roof installation process
Here is how a roofer typically installs an EPDM roof.
Deck prep
Damaged decking is replaced and drainage is confirmed before any insulation goes down. A tear-off comes first on existing roofs.
Add the cover board
Insulation boards go down for energy savings and slope, topped by a smooth cover board. Low spots can be corrected with tapered insulation.
Lay the sheet
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Seams are planned so they run with the slope.
Bond the membrane
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Tape edges are finished with lap sealant.
Flash the details
Perimeter edge metal, wall flashing and pipe boots complete the roof. The top edge is sealed and covered. The last step is probing each seam and patch for gaps.
What is included
What rubber roof installation covers
Deck preparation
The base is cleared and checked for a sound start.
Flashing
Every penetration and edge is sealed for a finished roof.
EPDM membrane
The rubber membrane is adhered or fastened over a clean, dry base.
Seam tape
Every seam gets primer and tape for a lasting bond.
Related service
EPDM Roof Installation Millburn, NJ
The quality of an EPDM installation shows up years later in the seams and edges. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Weather matters too, since adhesives and primers need dry conditions. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
A good Millburn installer also plans for movement. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
In Millburn, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Millburn and nearby towns like Vauxhall, Springfield, Short Hills and Union, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
For rubber roof installation in Millburn, NJ or nearby towns like Vauxhall, Springfield, Short Hills and Union, call (973) 858-1841 to reach a roofer who covers your street.
How the weather here affects roofs around Millburn
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Millburn, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Drier ceilings
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Millburn and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about rubber roof installation
Is a rubber roof the same as TPO?
The two are different materials. Black EPDM is taped and stretchy, and white TPO is welded and reflective. Each suits different roofs.
What color EPDM is best?
Color affects heat gain. Black EPDM absorbs heat, which can help in cold climates, while white EPDM reflects sunlight and keeps the rooms below cooler. Ask about both options.
How long does a new rubber roof last?
Rubber roofs often last decades. Good seams, drainage and occasional checks make the difference. Small repairs are easy to make.
Can a rubber roof go over an existing roof?
A recover is possible only under certain conditions. The old roof must be a single dry layer, with a recover board over it. Otherwise, a tear-off is needed. The roofer tests the old roof for moisture before recommending a recover.
Which EPDM thickness should I choose?
Most residential EPDM is 45 or 60 mil. The thicker sheet holds up better to traffic and weather. Even thicker sheets are available for demanding roofs.
More questions? Call (973) 858-1841
Often needed together
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, so water drains instead of ponding.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Tearing off or recovering a worn flat roof and installing a new membrane, insulation and edge metal, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Millburn, NJ?
Call now for Millburn rubber roof installation and help in the towns around it.